During the global economic recession that began in mid 2008, many companies found it diffi cult to gain enough credit in the form of short-term loans from their banks and other lenders. In some cases, this caused working capital problems as short-term cash fl ow defi cits could not be funded. Ultra-Uber Limited (UU), a large manufacturer based in an economically depressed region, had traditionally operated a voluntary supplier payment policy in which it was announced that all trade payables would be paid at or before 20 days and there would be no late payment. This was operated despite the normal payment terms being 30 days. The company gave the reason for this as ‘a desire to publicly demonstrate our social responsibility and support our valued suppliers, most of whom, like UU, also provide employment in this region’. In the 20 years the policy had been in place, the UU website proudly boasted that it had never been broken. Brian Mills, the chief executive often mentioned this as the basis of the company’s social responsibility. ‘Rather than trying to delay our payments to suppliers,’ he often said, ‘we support them and their cash flow. It’s the right thing to do.’ Most of the other directors, however, especially the fi nance director, think that the voluntary supplier payment policy is a mistake. Some say that it is a means of Brian Mills exercising his own ethical beliefs in a way that is not supported by others at UU Limited. When UU itself came under severe cash fl ow pressure in the summer of 2009 as a result of its bank’s failure to extend credit, the fi nance director told Brian Mills that UU’s liquidity problems would be greatly relieved if they took an average of 30 rather than the 20 days to pay suppliers. In addition, the manufacturing director said that he could offer another reason why the short-term liquidity at UU was a problem. He said that the credit control department was poor, taking approximately 50 days to receive payment from each customer. He also said that his own inventory control could be improved and he said he would look into that. It was pointed out to the manufacturing director that cost of goods sold was 65% of turnover and this proportion was continuously rising, driving down gross and profi t margins. Due to poor inventory controls, excessively high levels of inventory were held in store at all stages of production. The long-serving sales manager wanted to keep high levels of finished goods so that customers could buy from existing inventory and the manufacturing director wanted to keep high levels of raw materials and work-in-progress to give him minimum response times when a new order came in. One of the non-executive directors (NEDs) of UU Limited, Bob Ndumo, said that he could not work out why UU was in such a situation as no other company in which he was a NED was having liquidity problems. Bob Ndumo held a number of other NED positions but these were mainly in service-based companies. Required:
(a) Defi ne ‘liquidity risk’ and explain why it might be a signifi cant risk to UU Limited. (5 marks)
参考答案:
Liquidity risk Liquidity risk refers to the diffi culties that can arise from an inability of the company to meet its short-term fi nancing needs, i.e. its ratio of short-term assets to short-term liabilities. Specifi cally, this refers to the organisation’s working capital and meeting short-term cash fl ow needs. The essential elements of managing liquidity risk are, therefore, the controls over receivables, payables, cash and inventories. Manufacturing has historically had a greater challenge with the management of liquidity risk compared to some other sectors (especially low inventory businesses such as those in service industries like those that Bob Ndumo is NED for). In the case of UU, this is for three reasons. Firstly, manufacturing usually requires higher working capital levels because it buys in and sells physical inventory, both on credit. This means that both payables and receivables are relatively high. It also, by defi nition, requires inventory in the form of raw materials, work-in-progress and fi nished goods, and therefore the management of inventory turnover is one of the most important management tasks in manufacturing management. In addition, wages are paid throughout the manufacturing process, although it will take some time before fi nished goods are ready for sale. Secondly, manufacturing has complex management systems resulting from a more complex business model. Whilst other business models create their own liquidity problems, the variability and availability of inventory at different stages and the need to manage inventories at different levels of completion raises liquidity issues not present in many other types of business (such as service based business). Thirdly, UU has a number of weaknesses that amplify its structural liquidity position as a manufacturer. Its ineffective credit control department and its voluntary B0 day supplier payment policy both increase the short-term cash pressure and thereby increase the likelihood of liquidity risks becoming realised.